INDUSTRIAL ETHERNET SWITCHES

IGS-6325-8UP2S 8port Industrial Switch

L3. 4xSFP, Ring, PoE++, 48-54VDC

Product nr: 137468
279338

Physical Port

  • 8 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with 802.3bt PoE++ Injector function
  • 2 100/1000/2500BASE-X SFP slots for SFP type auto detection
  • One RJ45-to-RS232 console interface for basic management and setup

 

Industrial Hardened-design

  • Dual power input, redundant power with reverse polarity protection
  •          - DC 48 to 56V input
             - Active-active redundant power failure protection
             - Backup of catastrophic power failure on one supply
             - Fault tolerance and resilience
  • DIN-rail and wall-mountable design
  • IP30 aluminum case 
  • Supports 6000V DC Ethernet ESD protection
  • -40 to 75 degrees C operating temperature

 

Digital Input and Digital Output

  • 2 Digital Input (DI)
  • 2 Digital Output (DO)
  • Integrate sensors into auto alarm system
  • Transfer alarm to IP network via email and SNMP trap

 

802.3bt Power over Ethernet

  • Complies with IEEE 802.3bt Power over Ethernet Plus Plus Type-4 PSE
  • Backward compatible with IEEE 802.3at/af PD device
  • Up to 8 ports of IEEE 802.3af/IEEE 802.3at/IEEE 802.3bt PoE++ devices powered
  • Supports PoE power up to 95 watts for each PoE port
  • Total of 360-watt PoE budget
  • Auto detects powered device (PD)
  • Circuit protection prevents power interference between ports
  • Remote power feeding up to 100m
  • PoE management features
  •          - Total PoE power budget control
             - Per port PoE function enable/disable
             - PoE admin-mode control
             - PoE port power feeding priority
             - Per PoE port power limit
             - PD classification detection
             - PoE extend mode control to support power feeding up to a distance of up to 160 meters
  • Intelligent PoE features
  •          - Temperature threshold control
             - PoE usage threshold control
             - PD alive check
             - PoE schedule

 

Layer 3 IP Routing Features

  • IP dynamic routing protocol supports OSPFv2
  • IPv4/IPv6 hardware static routing
  • Routing interface provides per VLAN routing mode


Layer 2 Features

  • High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
  • Storm Control support
  •          - Broadcast/Multicast/Unicast
  • Supports VLAN
  •          - IEEE 802.1Q tagged VLAN
             - Up to 255 VLANs groups, out of 4095 VLAN IDs
             - Supports provider bridging (VLAN Q-in-Q IEEE 802.1ad)
             - Private VLAN Edge (PVE)
             - Protocol-based VLAN
             - MAC-based VLAN
             - Voice VLAN 
             - GVRP (GARP VLAN Registration Protocol)
  • Supports Spanning Tree Protocol
  •          - IEEE 802.1D Spanning Tree Protocol (STP)
             - IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
             - IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
             - BPDU Guard
  • Supports Link Aggregation
  •          - 802.3ad Link Aggregation Control Protocol (LACP)
             - Cisco ether-channel (static trunk)
             - Maximum 4 trunk groups with 4 ports per trunk group 
             - Up to 40Gbps bandwidth (duplex mode)
  • Provides port mirror (many-to-1)
  • Port mirroring to monitor the incoming or outgoing traffic on a particular port 
  • Loop protection to avoid broadcast loops
  • Link Layer Discovery Protocol (LLDP)
  • Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches
    and blocks the ports on both ends of the link if the link fails at any point between the two devices
  • Supports G.8032 ERPS (Ethernet Ring Protection Switching)
  • IEEE 1588 and Synchronous Ethernet network timing

 

Quality of Service

  • Ingress Shaper and Egress Rate Limit per port bandwidth control
  • 8 priority queues on all switch ports
  • Traffic classification
  •          - IEEE 802.1p CoS
             - IP TOS/DSCP/IP precedence
             - IP TCP/UDP port number
             - Typical network application
  • Strict priority and Weighted Round Robin (WRR) CoS policies
  • Supports QoS and In/Out bandwidth control on each port
  • Traffic-policing  on the switch port
  • DSCP remarking


Multicast

  • Supports IPv4 IGMP snooping v1, v2 and v3
  • Supports IPv6 MLD snooping v1 and v2
  • Querier mode support
  • IPv4 IGMP snooping port filtering
  • IPv6 MLD snooping port filtering
  • MVR (Multicast VLAN Registration)

 

Security

  • Authentication
  •          - IEEE 802.1X Port-based/MAC-based network access authentication
             - Built-in RADIUS client to cooperate with the RADIUS servers
             - TACACS+ login users access authentication
             - RADIUS/TACACS+ users access authentication
             - Guest VLAN assigns clients to a restricted VLAN with limited services
  • Access Control List
  •          - IP-based Access Control List (ACL)
             - MAC-based Access Control List
  • Source MAC/IP address binding
  • DHCP snooping to filter distrusted DHCP messages
  • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
  • IP Source Guard prevents IP spoofing attacks
  • IP address access management to prevent unauthorized intruder


Management

  • IPv4 and IPv6 dual stack management
  • Switch Management Interfaces
  •          - Console and Telnet Command Line Interface
             - HTTP web switch management
             - SNMP v1 and v2c switch management
             - SSH, TLS, SSL and SNMP v3 secure access
  • SNMP Management
  •          - Four RMON groups (history, statistics, alarms, and events)
             - SNMP trap for interface Link Up and Link Down notification
  • IPv6 IP address/NTP/DNS management
  • Built-in Trivial File Transfer Protocol (TFTP) client
  • BOOTP and DHCP for IP address assignment
  • System Maintenance
  •          - Firmware upload/download via HTTP/TFTP
             - Reset button for system reboot or reset to factory default
             - Dual Images
  • DHCP Relay
  • DHCP Option 82
  • DHCP Server
  • User Privilege levels control
  • Network Time Protocol (NTP)
  • Network Diagnostic
  • System Maintenance
  •          - SFP-DDM (Digital Diagnostic Monitor)
             - Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
             - ICMPv6/ICMPv4 remote ping
  • SMTP/Syslog remote alarm
  • System Log
  • PLANET Smart Discovery Utility for deployment management

For more information please see datasheet